GEN PT60 Kit Vaporesso

€ 40.00

Add to cart

GEN PT60 Kit Vaporesso 

The GEN PT60 is the new pod mod in GEN family designed for DTL users. It’s equipped with the new xTank pod. With Double Top System and SSS Leak-Resistant Technology, it gives a Quadra leak resistance, better than a tank.
The COREX inside – a flavor boosting technology, increases the flavor and the lifespan of GTX coil with innovation on the cotton and the MESH. It can also be fully compatible with the whole coil platform.

With Double Top System and SSS Leak-Resistant Technology, the xTank gives a Quadra leak resistance, better than a tank. The COREX inside increases the flavor and the lifespan of GTX coil with innovation on the cotton and the MESH. It all fits in the light and elegant GEN PT60

Available colours:
• Dark Black
• Matte Grey
• Earth Brown
• Alpine Green
• Aegean Blue

Main features: 
• Length: 28mm
• Width: 35mm
• Height: 112mm
• Tank Capacity: 2ml
• Display: 0.91'' OLED Screen
• Battery: 2500mAh (build in)
• Power Range: 5-80W
• Resistance Range: 0.03~5Ω
• Charging Current: DC 5V/2A Type-C

How to charge
 Easy to charge via USB Type-C port. When battery indicate that is full, disconnect the wire. Never leave connected for night time and never leave the device connected to the charger unattended. If you do, you do so at your own risk.

How to fill
Filling from the side. To fill the tank or top up the liquid, just open the rubber closure located on the side of the tank. After filling, make sure that the rubber closure is properly closed. If you have a new coil, set aside the freshly filled tank for 5-10 minutes for the coil to soak up properly. It will protect it from immediate burning.

Note:
1. Please don’t add e-liquid into the air pipe.
2. Please don’t overfill and make sure the e-liquid level is between 10%-90%.
3. Please first drip a few drops of e-liquid directly into the wick of the coil to make it fully saturated before first use.
4. Please use proper PG/VG ratio liquids for this type of tank





How to fit / exchange coil

1. Unscrew the thread base from the tank;
2. Lever the used coil by screwdriver, and pull it out;
3. Install a new coil to the tank;
4. Re-attach the thread base.
5. Screw the clearomizer onto your battery.


Vaporesso GEN PT60 Kit in Ireland vape ecigarette device

Sub ohm device. Worth reading before buying:
This type of device is intended for the user with grater knowledge and experience. Coils used are below 1.0 ohm so that higher Wattage could be used. Before you use please read manual. Often, this kits are equipped with additional options that allow you to adjust Wattage.

For Sub ohm devices we recommend that you do not use liquids with nicotine higher than 6mg / ml and only good quality liquids with 30/70 PG / VG or higher VG. Devices of this type produce a lot more of vape, which results in a stronger hit to the throat (like higher nicotine in the basic device). Ask if you're not sure ... we don't bite ;-)

The kit contains:

• 1 x GEN PT60 MOD - battery capacity 2500mAh
• 1 x xTANK POD (2ml)
• 1 x GTX 0.2Ω MESH Coil  (45-60W)
• 1 x GTX 0.4Ω MESH Coil (26-32W)
• 1 x Type-C USB Cable
• 1 x User Manual

The warranty period for particular kit elements is: 
2 months from date of purchase:
•  GEN PT60 MOD

The warranty does not cover Coils or Clearomizer, as these part are quickly used up while the products are put to normal use.

Tip - All batteries come with a 5-Click ON/OFF feature. This can help prevent you from unintentionally turning the battery ON. Simply press the button 5 times quickly in 2 seconds to turn the battery ON or OFF


IMPORTANT! When using a new atomizer / clearomizer, let the tank stand for 5 minutes, so the cotton can be saturated with juice before firing. Do not let the tank become completely empty. Refill the tank become completely empty. Refill the tank to avoid dry burning or damage to the atomizer / clearomizer.

Data sheet

  • Special offer - No

30 other products in the same category:

loading